Comment by Gshaheen
1 day ago
It’s the same story for basically any part of a home. Faucets, furniture, tubs, windows, doors, floors, lamps, you name it.
What a testament to the manufacturing advances that have made it profitable to cater to every possible taste, budget, and architectural layout. It’s incredible actually.
I just wish there was some way to replace the LEDs on these things when they inevitably die. And, no matter what large number of years or decades are slathered on the box, inevitably at least one LED panel will blow out three to six months after purchase, nominally still in warranty but good luck getting any service under it, I'm sure. If there was, there could be a place for at least some of these in a house, but the amount of crap that you have no choice but to throw out as soon as the LEDs fry is insane.
This is why my "fancy" lighting fixture is an old track (whose proprietary lights died a long time ago) wrapped with an extension cable with 5 standard sockets on it, and some standard light bulbs in it. We dress it up with ribbons and stuff for the seasons. It doesn't look as nice as any of the things in that article, not even the gaudy and tasteless ones, but when a bulb burn out, I put a new one in and get on with life, I don't throw out an entire fan and buy a new one.
I'm old enough to remember when I was promised LEDs would last approximately forever without having to be replaced.
Your local inspector may have opinions about this, but you can buy all the components of an excellent LED system from your favorite electronics distributor, e.g. DigiKey.
Don’t waste your time or eyeballs with “driverless” devices. Get a chip-on-board LED, e.g. Bridgelux’s products, along with a matching driver (I like Luminus Devices’ small drivers - they have good startup and dimming behavior).
Aside from usual electrical safety, anyone designing what is effectively a luminaire needs to make sure that the driver matches the LED and that the driver is compatible with the dimmer in use. Matching the LED means that the driver produces an amount of current that that LED’s datasheet data is acceptable and that produces the amount of light that is desired and dissipates an amount of heat that can be managed. And that the LED’s voltage drop at the design current is in range for the driver. These LEDs are constant current devices, so you’re thinking about current first and voltage second. Read the datasheets!
Unfortunately many cheap luminaires are based on modules that are either driverless LEDs (which are terrible due to essentially unavoidable flicker and lack of regulation) or are line-voltage-supplied integrated devices. These are likely to be hard-to-find modules. There may not be room for a discrete driver and separate LED.
LEDs rarely die unless cooling is inadequate. DC/DC and AC/DC circuitry is a far more likely culprit.
In either case, learn to do hot air rework?
Yeah. It's not just cost, it's time. If I have to replace the fan, that's a trip to a hardware store, then a half hour (at least) to remove the old and install the new and get it wired correctly, so that it works and doesn't burn my house down. Then I have to take the old one apart far enough to fit it into the garbage can.
Replacing a bulb is a trip to my stash of bulbs in the laundry room, then throwing the old one in the trash.
I don't have time in my life for a fan with non-replaceable bulbs.
Have you tried replacing the LEDs or have you just assumed it's impossible because it's not a bulb?
I know how to solder tiny parts and big parts, and I'm actually pretty good at it. I can generally take complex things apart non-destructively and reassemble them without damage. I can use a meter. I understand how electronic components work, and I even find pleasure in using them. I can safely troubleshoot and repair or replace a power supply.
Fixing an LED fixture is within my wheelhouse. I can repair them.
I just don't want to.
It seems like a much better use of my time and money to just screw in a different light bulb and forget about it.
It depends on the specific fixture.
But then, the problem is, it depends on the specific fixture. They aren't exactly putting "EASY TO REPLACE LEDS" on the box. I can't climb up to the store display model and start hacking away at it to see if I can get to the LEDs, replace them, and reassemble it correctly.
What I saw last time I was in a store where the fixtures were on eye level looked like a lot of glue, one-way tabs, and LED strips of unknown and custom provenance were being used. I'm not really looking for this sort of experience in a lighting fixture. YMMV and more power to you.
> I'm old enough to remember when I was promised LEDs would last approximately forever without having to be replaced.
Yep, I remember that when Obama banned most incandescent lights because 'LED lighting is the future and 100 year lifespans blabla'.
Mind you, we used CFLs in the warm season, and incandescent in cold seasons. Incandescents are 100% efficient in cold seasons (heater AND light).
As much as I deign to admit, Trump reversed Obama's ban. And Biden reinstated it. I don't think Trump reversed Biden's reinstatement though. He's been way too busy with wrecking the country for shits and giggles.
But what the LED manufacturers figured out is they could overdrive LEDs and use substandard electronics for driving them. So sure, LEDs are more efficient, but they're the same old burnout cycle that's forced on us.
And we know all of this by the fact that Phillips makes "Dubai Lamps", and you can't buy them at any price. https://hackaday.com/2021/01/17/leds-from-dubai-the-royal-li...
> Incandescents are 100% efficient in cold seasons (heater AND light).
That's resistive heating, which is the most inefficient means of heating. Worse than natural gas or heating oil, and much worse than a heat pump.
3 replies →
I regret to inform you that Obama did not ban any light bulbs.
Those initiatives were first legislated during the Bush administration in 2007.
They were rolled back some during Trump's first term, in 2019.
Restrictions were re-introduced under Biden, in 2022.
I don't care much on the politics of it all because I do think a lot of it is silly, especially with how profit-motivated companies will still find a way to profit.
I will say I've had a number of Hue bulbs starting back in about 2018 and have yet to lose one except for a surge that got an unprotected strip. Otherwise, plenty of white and color bulbs have worked steadfast for nearly a decade while costing a fraction in energy. That said, I do miss the warmth of incandescent lighting, but I don't miss replacing bulbs multiple times a year
> every possible taste, budget, and architectural layout
Except "traditional" it seems.
Or “fit for purpose”.
> The sea was purple. The beach they were on was composed of tiny yellow and green pebbles - presumably terribly precious stones. The mountains in the distance seemed soft and undulating with red peaks. Nearby stood a solid silver beach table with a frilly mauve parasol and silver tassles.
> In the sky a huge sign appeared, replacing the catalogue number. It said, Whatever your tastes, Magrathea can cater for you. We are not proud.
Hitchhiker’s Guide to the Galaxy
And also to flood the market with an ocean of cheap, disposable crap that won't even function very well as a fan.
Except that it doesn't.
All of the stuff available is basically a mix of the elements the author puts on his 8 images on the beginning of the article. Where only 2 of them have fans that can actually vent a room.