Comment by insaneirish
2 years ago
As far as countertops go, field cuts are rather uncommon. Laser templating works well.
Holes on the other hand tend to be done in the field. But, people don't wear PPE even though it's simple and easy to do.
2 years ago
As far as countertops go, field cuts are rather uncommon. Laser templating works well.
Holes on the other hand tend to be done in the field. But, people don't wear PPE even though it's simple and easy to do.
Due to lack of tech work I've been installing stone countertops. I can confirm we cut on site around half the time, microplastics galore (you can smell the polyester in the air).
Would love to know your opinion on this then - is there any way onsite cutting could be eliminated, semi or fully automated with wet cutting? Or is the onus always on the contractor to use PPE?
The slabs should be "perfect" from the shop. This includes sink cutouts. For whatever reason, there is a tendency for faucet holes to be cut onsite. This bothers me, but it's true.
Not only is it stupidly messy, it's less precise, dangerous, and often the crews are too careless to protect the inside of the cabinet boxes (where the slug of stone that's being cut from the top will drop and bounce around).
It's on the contractor to use PPE. At my outfit we measure, take a few notes, do most of the cutting and polishing wet at the workshop. But often the hole for the faucet is cut on site after the sink is glued under the countertop in place, there is always dust, I'd rather program in JavaScript;)
I'd love to hear why. What is the templating process and why is it not better?
Show me a job site with square drywall and I'll show you a perfect fitting countertop:) The material is mostly cut with a diamond saw with a water jet to keep the dust down. But if an adjustment is needed there is often some cutting and polishing on site.
3 replies →
I’ve watched a contractor cut holes in a countertop in the field. They did it wet. I’d still wear safety glasses if I were doing this, but IIRC there was no dust.
I’ve never seen someone cut a countertop on site. They do it in a shop. (Why didn’t Australia instead ban all countertop cutting in shops that doesn’t use dustless tools?)
Hmm, I just looked it up. Home Depot sells the tool for under $30.
I made an at home modification to our stone counter top when replacing the stove/oven. The new unit was 1/4" too wide. I did the whole tenting and wet cutting, but not nearly wet enough for the obvious reason. I was in full spaceman suit though, as I was sure the amount of water wasn't going to cut it.
I would NOT recommend this to anyone though. At the time, the turn time and expense of having the counter removed, altered at a proper shop, redelivered and installed was prohibitively expensive.
Just because you can’t see the dust doesn’t mean there isn’t dust. Often it’s the tiniest particles that are the most dangerous because they can attach to the walls of the lungs but are too small to then actually be dislodged by, a say, coughing.
I haven’t looked for lab data, but certainly what appears to happen is that the swarf ends up suspended in the water. Some water will spray, which will be a bit messy, but mostly it will be in droplets that don’t stay in the air. (And presumably aren’t going to get to one’s lungs either.) And the majority of the swarf just stays in a puddle.
This is in contrast to cutting dry, which causes all the swarf to fly into the air.
So the exposure isn’t zero, but it’s low. It would be interesting to see if it registers on a particle counter (Plantower, etc).
>But, people don't wear PPE even though it's simple and easy to do.
are you saying that wearing the PPE is simple and easy to do, or did you mean they don't wear PPE because the job is so simple and easy to do?
The first. Workers tend to be lazy. How many guys do you see all the time using noisy commercial lawn equipment without any sort of hearing or eye protection? Those guys will all be deaf (if lucky) or have severe tinnitus (if unlucky) by 50.
You see it in factories too, where workers will disable safety devices just to save them a tiny amount of movement.
~6 years ago I got new countertops, and while they did the bulk of the cutting in their facility, they did do a few cuts in my front yard, creating a huge cloud of dust. The main parts of the counter arrived ready to assemble, but I think they cut a spanning piece for behind the stove, spanning the counters on either side.
My 8yo son came out to see what was going on, looked at the workers doing the cut without masks, and said "silicosis ain't no joke" and went back inside. I've taught him well.
All the workers clapped and one of them cried.
And who was that boy? Albert Einstein.
I'll take things that never happened for $500, linsomniac
I'm struggling to figure out why it would seem so implausible. I got the phrasing from AvE on youtube, and I've said it to him several times during our DIYing together because I'm trying to educate him on using PPE.
2 replies →
My exact experience! Got a hole added for water filter tap and I think he didn’t wear PPE. Had I known about this I would have ensured everyone out the house while it was being done.
> people don't wear PPE even though it's simple and easy to do
Maybe we should mandate people wear PPE, but if they decide to flaunt the rules and risk their health for no reason, I just don't really feel all that sympathetic.