AIUI, Tesla really screwed the pooch here. For the original Model S, Tesla really really wanted the US model to tuck the charge socket under the little hinged reflector, and they couldn’t figure out how to fit the Type 2 “Mennekes” connector their. So they invented their own socket (which evolved into NACS), and the Tesla one is rather inferior to Type 2, at least when used for AC charging.
And now every EV needs to have a different charge port configuration for North America vs Europe, and North America is stuck with NACS. (NACS is fine for DC but still sucks for AC. It cannot support 3-phase charging (which I admit has always seemed like a silly feature except in the limited case of 1 or 2 chargers in a single family residence), and cables and adapters cannot passively report their current rating. So you would need to build a kind of gnarly active MITM system to make a safe extension cable, whereas a Type 2 to Type 2 cable is built part of the Type 2 design.
Later, Tesla proved the whole thing pointless by successfully fitting Type 2 in the same location…
I think the timeline is a bit off. When Tesla designed its connector, Type 2 wasn’t yet the established European standard. Tesla had shown its proprietary connector by 2011 and shipped it in 2012; Type 2 wasn’t selected as Europe’s common connector until 2013.
When Tesla later engineered the European Model S, it needed three-phase AC and adopted a modified Type 2 connector, which fitted behind essentially the same tail light door.
But that’s all history now.
Arguably both markets ended up with good solutions for their needs: NACS is exceptionally compact and well suited to North American single-phase AC plus DC fast charging, while Type 2 is larger but supports Europe’s widespread three-phase AC.
> Arguably both markets ended up with good solutions for their needs
Only because everyone aimed too low. NACS (as mentioned before) doesn’t cleanly support adapters or detachable cables. And CCS Combo 2 is unnecessarily clunky. And you end up in a rather awkward position if you ship a car from the EU to North America or vice versa.
It ought to be entirely straightforward to design a standardized cable, NACS at one end and with a new interface at the other, that can attach and detach from a compact and weather resistant charge port. It would be fully compatible with all NACS vehicles, and it would achieve this by negotiating voltage and current limits with the EVSE at the other (newly specified) end.
It could even be cheap in a low-current version — it would basically be an extension cord, with two 12AWG hots and a ground plus a couple of little wires and the whatever inexpensive electrical parts are needed to declare its capabilities. If you can buy an e-marked USB-C cable for a few dollars, the latter won’t cost much.
European Model S has Type 2 in that location, only ones that don't fit is the Type 2 CCS with giant DCFC pins below the regular Type 2. NACS is just Tesla doing Apple.
NACS is far less clunky than CCS. And don’t get me started on ChaDeMo - my best guess is that whoever designed it thought that big heavy awkward gasoline nozzles where cool and wanted their EV chargers to be at least as massive.
3 phase has a property that the total power is (with fully balanced loads and no harmonics) constant. But n phases, equally spaced in phase angle, each an RMS voltage V from ground, with RMS current I per phase in phase with the voltage to ground, gives power n•V•I. (I’m assuming that n>=2 so that there is no neutral current.) There’s no savings for n=3 vs n=2.
There is a savings over the system in which you use 2 of 3 phases, which gives unbalanced phase angles. And that system is widely used in the US in non-single-family installations. But if you have a bunch of chargers, you put 1/3 of them on each of the pairs of phases, and everything balances back out at the panel whenever a decent number of chargers are in use.
Maybe, if a a car could rely on having 3 phases, it could avoid some ripple filtering by taking advantage of constant supply power (no 2f component), but cars need to be able to charge from a single phase even in Europe.
No, the cable you carry for AC charging has a Type 2 connector on both sides, it's purely an EV charging cable. It's not the same 3-phase plug you'd plug a table saw into.
AIUI, Tesla really screwed the pooch here. For the original Model S, Tesla really really wanted the US model to tuck the charge socket under the little hinged reflector, and they couldn’t figure out how to fit the Type 2 “Mennekes” connector their. So they invented their own socket (which evolved into NACS), and the Tesla one is rather inferior to Type 2, at least when used for AC charging.
And now every EV needs to have a different charge port configuration for North America vs Europe, and North America is stuck with NACS. (NACS is fine for DC but still sucks for AC. It cannot support 3-phase charging (which I admit has always seemed like a silly feature except in the limited case of 1 or 2 chargers in a single family residence), and cables and adapters cannot passively report their current rating. So you would need to build a kind of gnarly active MITM system to make a safe extension cable, whereas a Type 2 to Type 2 cable is built part of the Type 2 design.
Later, Tesla proved the whole thing pointless by successfully fitting Type 2 in the same location…
I think the timeline is a bit off. When Tesla designed its connector, Type 2 wasn’t yet the established European standard. Tesla had shown its proprietary connector by 2011 and shipped it in 2012; Type 2 wasn’t selected as Europe’s common connector until 2013.
When Tesla later engineered the European Model S, it needed three-phase AC and adopted a modified Type 2 connector, which fitted behind essentially the same tail light door.
But that’s all history now.
Arguably both markets ended up with good solutions for their needs: NACS is exceptionally compact and well suited to North American single-phase AC plus DC fast charging, while Type 2 is larger but supports Europe’s widespread three-phase AC.
> Arguably both markets ended up with good solutions for their needs
Only because everyone aimed too low. NACS (as mentioned before) doesn’t cleanly support adapters or detachable cables. And CCS Combo 2 is unnecessarily clunky. And you end up in a rather awkward position if you ship a car from the EU to North America or vice versa.
It ought to be entirely straightforward to design a standardized cable, NACS at one end and with a new interface at the other, that can attach and detach from a compact and weather resistant charge port. It would be fully compatible with all NACS vehicles, and it would achieve this by negotiating voltage and current limits with the EVSE at the other (newly specified) end.
It could even be cheap in a low-current version — it would basically be an extension cord, with two 12AWG hots and a ground plus a couple of little wires and the whatever inexpensive electrical parts are needed to declare its capabilities. If you can buy an e-marked USB-C cable for a few dollars, the latter won’t cost much.
European Model S has Type 2 in that location, only ones that don't fit is the Type 2 CCS with giant DCFC pins below the regular Type 2. NACS is just Tesla doing Apple.
NACS is far less clunky than CCS. And don’t get me started on ChaDeMo - my best guess is that whoever designed it thought that big heavy awkward gasoline nozzles where cool and wanted their EV chargers to be at least as massive.
> 3-phase charging (which I admit has always seemed like a silly feature
Well, 3phase is more efficient as you have less losses in the cabling.
May save you 5-10% on the bill.
3 phase has a property that the total power is (with fully balanced loads and no harmonics) constant. But n phases, equally spaced in phase angle, each an RMS voltage V from ground, with RMS current I per phase in phase with the voltage to ground, gives power n•V•I. (I’m assuming that n>=2 so that there is no neutral current.) There’s no savings for n=3 vs n=2.
There is a savings over the system in which you use 2 of 3 phases, which gives unbalanced phase angles. And that system is widely used in the US in non-single-family installations. But if you have a bunch of chargers, you put 1/3 of them on each of the pairs of phases, and everything balances back out at the panel whenever a decent number of chargers are in use.
Maybe, if a a car could rely on having 3 phases, it could avoid some ripple filtering by taking advantage of constant supply power (no 2f component), but cars need to be able to charge from a single phase even in Europe.
The point is that EVSE plugs are safer and European dryer plugs under the rain out in the open is technically kind of dangerous.
No, the cable you carry for AC charging has a Type 2 connector on both sides, it's purely an EV charging cable. It's not the same 3-phase plug you'd plug a table saw into.